![]() If a follower has a turned on round-baler or a bale-wrapper, it will now automatically unload the bale. The offset can be toggled between 'zero' and 'last offset value' (RIGHT CTRL + X), or inverted (press-and-hold RIGHT CTRL + X). Left/right offset is set using RIGHT CTRL + A/D, in increments of approximate 0.5 meter. Positive values are "keep back" distance (up to +250), and negative values are "in front" (up to -50).ĭo please note that current there are no traffic-collision-triggerboxes, so vehicles will not be able to detect when/if they collide into the leading vehicle or some other vehicle - so you better set the distance further back. The follow distance can be set using RIGHT CTRL + W/S, in increments of approximate 5 meters. To stop following, press the same action again (RIGHT CTRL + F). It is possible to "pause" driving, and then later "resume" following the leader's trail, using the wait/resume action (RIGHT CTRL + H). If no "trail crumbs" can be found, or the vehicle already is followed by another, a warning will appear and you will have to either move a little bit further towards/back, or change to follow another vehicle. To follow some vehicle, point your own vehicle towards it and press the start action (RIGHT CTRL + F). Note: Each set of action-keys must use the same modifier-key! Press-and-hold RIGHT SHIFT + W/S to repeat decrease/increase in steps of 1. Press-and-hold RIGHT SHIFT + X = Invert the follower's offset (left-to-right, right-to-left). RIGHT SHIFT + X = Toggle the follower's offset between zero and last value. RIGHT SHIFT + A/D = Adjust the follower's left/right offset, in steps of 0.5. RIGHT SHIFT + W/S = Decrease/increase the follower's distance to me, in steps of 5. RIGHT SHIFT + H = Pause/resume the follower. Press-and-hold RIGHT CTRL + W/S to repeat decrease/increase in steps of 1.īehind - To control the vehicle that is following behind me (if any): Press-and-hold RIGHT CTRL + X = Invert the offset (left-to-right, right-to-left). RIGHT CTRL + X = Toggle offset between zero and last value. RIGHT CTRL + A/D = Adjust left/right offset when following, in steps of 0.5. RIGHT CTRL + W/S = Decrease/increase following distance, in steps of 5. RIGHT CTRL + F = Start/stop following the vehicle in front (if possible). Myself - For the vehicle the player is driving: Not two separate columns like FS17 was.The action-keys, which can be changed in Options - Controls, are defined in two sets: It did recognize the joystick just fine.Īlso when in the button configured screen if you click gamepad it looks like it supports two separate gamepads however all controls for both gamepads were in the same column. The game recognized my wheel and pedals as a B655 or something like that. However it was after midnight and I had to be at work at 7am. Once I felt ok with the wheel and pedals I then plugged the joystick in and configured the buttons for it again and then loaded up the sim. ![]() ![]() I think it may be fixed at this point so I load up the game and for the most part the wheel and pedals work fine however there is no adjustment for the force feedback and it is pretty strong. When I did this it actually showed the pedal axis instead of buttons R2 and L2. I then unplugged the joystick and configured just the wheel and pedals only. Some how the icon flickering stopped but the controls were still screwed up. I also unplugged the joystick and then plugged it back in. I started with a full system reboot and then when I loaded the game up I unplugged my wheel and pedals and plugged them back in. The controls were totally backwards and screwed up. I configured the buttons and started the game. When I started the game last night I had both controllers plugged into my computer. For reference I am using the thrust master T150 pro wheel and 3 pedal set along with the thrust master 1600 joystick. I had the same problems last night as most of you.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |